Change Currency: GBP

Follow Us Now

How to Splice Rope

 

Splicing will reduce the overall length of the rope and care should be taken to allow for this. When splicing in house we keep this to around 60cm spliced plus the doubled section of the eye.

Eye Splice on Double braid Polyester

These splicing demonstrations are courtesy of Selma, the Norwegianmanufacture of the Selma Fids SplicingNeedles.

Mark the rope a needle length from theend (A).

Mark again at (B) according to the loop size. Tie a knot
about 60 in. from (B).

Extract the core at (B) using a small needle.

Take out the slack from the cover by sliding your hand
from the knot towards (B).

Withdraw another needle - length of core from (B) and mark this point (C).

Withdraw another 2/3 of a needle and mark it (D) on the core.

To make the splicing easy, extract some more coreand make a lock on using a small needle near (B).

Find the right needle for splicing and feed the cover-end into the needle (C) and take it out at (D).

Remove the needleand pull cover back into core until the end is hidden.

Attach thecore-end into the needle and insert a needlenear (C) and out of cover in one past (B).

Pull the core through the cover until the slack is taken up.

Get the splice (C-D) into thecover by sliding the cover back
over until it reaches point (A).

Point (A) and (B) should now meet.

Cut off the exposed core and stretch the eye until thecore goes under the cover.

You have nowmade a perfect eye-splice.

If you want toinsert a thimble, the eye-size is to be calculated less thanthe circumference of the thimble.

If desired a thimble can be inserted. Press cover towards thimble, and secure by whipping with twine.

 

 

Eye Splice on Three strand Ropes

These splicing demonstrations are courtesy of Selma, the Norwegianmanufacture of the Selma Fids SplicingNeedles.

Untwist the strands and make 1, 2 and 3 ready.
Decide eye size.

Put strand 1 under upper strand of rope.

Turn eye anticlockwise until strand 2 is up.

 

 

Put strand 2 under strand of rope next to cord 1.

Turn eye anticlockwise until 3 is up.

Put strand 3 under cord of rope next to strand 2.

You have now made one round of splicing.

Tighten up strands after each round.

Start second round by going with strand 1 over strand of rope and under the next.

Do the same with strand 2 and 3.

Do four rounds with all strands.

Cut ends near rope and the splice is finished!

 

 





 

Tapering D2 and V2

 

Decide where you would like to taper the rope and lock stitch the cover to the core using some whipping twine.

 

 

Measure 30cm down from the lock stitch and bunch up the cover of the rope. Then cut across the rope from one of the markers until this marker appears again taking care not to cut the core. The cover will open up and you can discard the cover you do not want.

 

 

Take a splicing fid and pick out the plaits of the rope 1cm down from the lock stitch until all of the plaits have been released.

 

 

Take a large splicing needle and insert it into the core of the rope 35cm from the lock stitch towards the lockstitch.

 

 

Push the needle through the centre of the core until it emerges 1cm in front of the lock stitch where you have picked out the cover plaits.

 

 

Tape the separated cover plaits together and insert through the eye of the needle. Then pull needle out of the core taking the cover with it.

 

 

Once the needle has emerged from the core remove the cover from the needle and cut away the tape, then milk the core back over the cover until the cover disappears.

 

 

Then take some whipping twine and whip over the join between the core and cover.

Kingbraid/Marlowbraid or Mattbraid Covered Eye Splice

 

Tie knot 3 meters from end then cut off heat sealed end, pushing back outer case exposing 10cms of inner core. Holding end of case to the core, push back slack for 1 meter.

 

 

Mark 'A' 30cms from end. Form eye size, mark 'B' on standing part of rope.

 

 

Open cover at 'B', and pull out core, taping it with rigging tape opposite 'A'.

 

 

From tape, reduce core by 50% and tape loose ends, pushing slack back to 'B' until core starts to move. Insert needle 35cms from 'B' and, taking care not to ensnare core, push needle down inside outer case until it emerges at 'A'.

 

 

Thread core tail into eye of needle pull out of rope until eye has formed and end of core has emerged.

 

 

Unpick and cut out 6 yarn ends 5cms from eye end of case tail. Push back some slack towards the eye ready for next stage. Insert needle 20cms from neck of the eye, emerging at 'A/B', thread cover into needle and pull down through rope.

 

 

Pull tight, give the splice a good shock to bed the yarns down, and cut off ends. Finally, run a hand over cover from eye end downwards until the ends disappear inside the rope.

 

 

If a thimble is required, insert while eye is being formed, before ends are pulled tight.

 

 

 

Ropes

 

 

Information

Join Us On
 

    

                   

copyright© 2006-2019 outdoor xscape rope company

Mobile Site